BS 300 PLUS GH is the BS version with gravity autocut. The machine is suitable to cut both left and right (up to 60° on the left and 45° right). The machine is versatile working tool able to realize small and medium batch production and an easy to use working tool that can be used either in mechanics and steelwork.
video Other infos DownloadCutting capacity at 90° |
Round 255 mm. Square 230 mm. Rectangular 300x180mm |
Cutting capacity at 45° right |
Round 210 mm. Square 190 mm. Rectangular 200x180mm |
Cutting capacity at 45° left |
Round 180 mm. Square 160 mm. Rectangular 180x100mm |
Cutting capacity at 60° left |
Round 135 mm. Square 110 mm. Rectangular 130x100mm |
Maximum capacity for full materials |
180mm |
Blade size. |
2765x27x0,9 |
End-cutting bandsaw inclination |
3° |
Blade motor |
1,5/1,8 kw |
Blade speed |
35/70 15÷110 m/min |
Hydraulic unit motor power |
kw 0,37 |
Hydraulic united tank |
Lt 12 |
Coolant tank |
Lt 20 |
Size |
1230x1700x1750 mm |
Working table height |
940 mm |
Weight |
412kg |
BS 300 PLUS is equipped with a wide diameter working area and a system of automatic easy stops at 0°, 45° and 60° left and 45° right with graduated plate to identify and set different angles.
The vice has adjustable guides, free to move alongside the worktable, with rapid approaching and camping.
Machine sawframe is rigid cast-iron with tubolar section, 320 mm pulleys, high blade tension at 1700 kg/cm2 and to avoid an excessive strain on the blade with frontal regulation and microswitch conroller.
A carter protect che blade, allowing to have easy access for maintentance when needed; a system with blade guides with hard pads, additional lateral bearings provides for the perfect allignment of the blade
GH version has a 3-mode selector:
Manual cut
Fast approach to the material
Automatic cut with adjustable down-feed rate and stop at cutting ending. The user can move manually the sawframe close to the material, then let the machine makes the cut adjusting only the down-feed rate.
Safe starting through the button on the handle with warning light to inform the use about the correct machine functioning. Coolant-tank and electropump are placed inside the floor stand.
If required, the electronic inverter for variable blade speed allows the operator via keyboard to adjust the machine to be able to cut a wide range of materials and different sections. The change of speed is via inverter and it does not affect the power of the engine even at low speeds.
It is possible to require , for all Imet machines, the minimal lubrication system , it avoids the dispersion of refrigerant liquid typical in the use of emulsifiable oil, the life of the blade is not in any way affected.
Adapter to synchronize the RTP/RTD table with sawframe motion.
Pneumatic vice, opening/closing synchronised with the sawframe motion
Bi-metal blade 2765x27x0.9 mm
Connection element for unloading table, equipped with one roller and a slide to collect the coolant
Loading/unloading table 1st element, 2 m long, max capacity kg 700.
Loading/unloading table following element, 2m long, max capacity 600kg.
Unloading roller table with metric rod and length stop, 1st element, 2m long, maximum capacity 700kg
Unloading roller table with metric rod and length stop, following elemnt, 2m long, maximum capacity 600kg
Unloading roller table with length measurement view system and manual positioning. RTD2LW30
unloading table with length measurement view system, manual positioning, capacity 700kg length 2m RTD4LW30
unloading table with length measurement view system, manual positioning, capacity 1300kg length 4m RTD6LW30
unloading table with length measurement view system, manual positioning, capacity 1900kg length 6m
Unloading table with motorized length stop, selection the lenghs with keyboard. RTP3W30
Unloading table with motorizedn length stop and selection of the lengths via keayboad, 3m, 1300kg. RTP6W30
Unloading table with motorizedn length stop and selection of the lengths via keayboad, 6m, 1900kg. RTP9W30
Unloading table with motorizedn length stop and selection of the lengths via keayboad, 9m, 2700kg
Unloadng roller table with digitale reading and manual positioning. RTL3W30
measurement length 3m, maximum capacity 3000kg RTL6W30
measurement length 6m, maximum capacity 6000kg RTL9W30
measurement length 9m, maximum capacity 9000kg
Pair of vertical rollers 300 mm made in steel, max 2 pairs for each element 2m long. To use without rollers covers.
BS 300 PLUS is equipped with a wide diameter working area and a system of automatic easy stops at 0°, 45° and 60° left and 45° right with graduated plate to identify and set different angles.
The vice has adjustable guides, free to move alongside the worktable, with rapid approaching and camping.
Machine sawframe is rigid cast-iron with tubolar section, 320 mm pulleys, high blade tension at 1700 kg/cm2 and to avoid an excessive strain on the blade with frontal regulation and microswitch conroller.
A carter protect che blade, allowing to have easy access for maintentance when needed; a system with blade guides with hard pads, additional lateral bearings provides for the perfect allignment of the blade
GH version has a 3-mode selector:
Manual cut
Fast approach to the material
Automatic cut with adjustable down-feed rate and stop at cutting ending. The user can move manually the sawframe close to the material, then let the machine makes the cut adjusting only the down-feed rate.
Safe starting through the button on the handle with warning light to inform the use about the correct machine functioning. Coolant-tank and electropump are placed inside the floor stand.
If required, the electronic inverter for variable blade speed allows the operator via keyboard to adjust the machine to be able to cut a wide range of materials and different sections. The change of speed is via inverter and it does not affect the power of the engine even at low speeds.
It is possible to require , for all Imet machines, the minimal lubrication system , it avoids the dispersion of refrigerant liquid typical in the use of emulsifiable oil, the life of the blade is not in any way affected.
Adapter to synchronize the RTP/RTD table with sawframe motion.
Pneumatic vice, opening/closing synchronised with the sawframe motion
Bi-metal blade 2765x27x0.9 mm
Connection element for unloading table, equipped with one roller and a slide to collect the coolant
Loading/unloading table 1st element, 2 m long, max capacity kg 700.
Loading/unloading table following element, 2m long, max capacity 600kg.
Unloading roller table with metric rod and length stop, 1st element, 2m long, maximum capacity 700kg
Unloading roller table with metric rod and length stop, following elemnt, 2m long, maximum capacity 600kg
Unloading roller table with length measurement view system and manual positioning. RTD2LW30
unloading table with length measurement view system, manual positioning, capacity 700kg length 2m RTD4LW30
unloading table with length measurement view system, manual positioning, capacity 1300kg length 4m RTD6LW30
unloading table with length measurement view system, manual positioning, capacity 1900kg length 6m
Unloading table with motorized length stop, selection the lenghs with keyboard. RTP3W30
Unloading table with motorizedn length stop and selection of the lengths via keayboad, 3m, 1300kg. RTP6W30
Unloading table with motorizedn length stop and selection of the lengths via keayboad, 6m, 1900kg. RTP9W30
Unloading table with motorizedn length stop and selection of the lengths via keayboad, 9m, 2700kg
Unloadng roller table with digitale reading and manual positioning. RTL3W30
measurement length 3m, maximum capacity 3000kg RTL6W30
measurement length 6m, maximum capacity 6000kg RTL9W30
measurement length 9m, maximum capacity 9000kg
Pair of vertical rollers 300 mm made in steel, max 2 pairs for each element 2m long. To use without rollers covers.